• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a loose door upvc window hinge repair is a simple task for most homeowners. If the holes for screws have been stripped and will not hold screws, you may need to use wood glue and dowels to fix the hinge.

Before you do this, however, brush away the surface rust. This will aid in keeping the dowels in place and give them a solid foundation for them to rest on.

Take the Hinges off

Many standard door hinges are able to be removed, making it easier to move the door from one side to the next or to remove the entire double glazing door hinges off of the frame should it be needed. Removing the hinges is fairly simple for anyone with a bit of patience, but you need to know how do it right.

If the hinges have been painted it is necessary to remove the paint before you attempt to remove the pins. If you do not, the paint may peel off and scratch your door when you try to lift it. To break the seal, place the hinges in a stainless steel dish and fill the pan with water until the hinges are fully submerged. The hinges should remain in the pan for approximately 30 minutes. The heat from the water should soften the paint and make it easier to take off the pins.

After the pins have been loosen and the pins are loose, you can take off the hinges from the door and frame. It is possible to use a standard screwdriver, but it is recommended to use a magnetic screwdriver for this task. This type of screwdriver has been specifically designed to take out metal screws and will assist you in getting the task completed much quicker.

Before you attempt to remove the hinges, it is a good idea to spray them with a lubricant. A simple lubricant will allow you to move the process along faster and also remove the pins and screws more easily. This type of lubricant can be found in most hardware stores as well as home improvement shops.

It is important to keep in mind that the number of door hinges you will need will differ based on the kind of door and its setting. Heavier doors and solid-core upvc doors hinges will require more hinges, while hollow-core doors that weigh less might only require two or three hinges.

It is also essential to know the various types of hinges to determine which ones will best suit your needs. Exterior hinges are designed to hold the weight of a door, but interior hinges must be able to handle heavier loads.

Reattaching the Hinges

Over time, the hinges of doors may loosen and begin to slide or hang crookedly. It could be a huge problem, but the fix is usually easy. Most of the time, a simple retightening of the screw will resolve the issue. However, if the screw holes have been stripped out, this may be more difficult to accomplish. A wood dowel could be used to tighten the holes again.

Start by drilling the hole with a drill bit close to the size of the new screw (normally 3/8"). Then, use wood glue and a wooden dowel to fill the hole. The dowel should be cut to a length that is exactly the same as the screw to ensure a snug fit. After that, reinstall the screw and tighten it until the desired tightness. If the door has a tendency to bind, then add another dowel to the gap and repeat the procedure. Make sure to close the double glazed door hinges slowly to examine the clearances around the perimeter after each adjustment.

Another option is to use the wood plug instead of dowel. This is also a viable option, but may take a bit longer to install. You can use the wood piece that has been whittled to the proper size. If you don't have a wooden tool You can also make use of toothpicks or wooden matches.

Once you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the screw's head smaller so that it does not touch the edge of the door when it's opened and closed. This will make it much easier to tighten the screws when reinstalling hinges.

After you have reinstalled the hinge, be sure to coat it with a dry lubricant to ensure that it doesn't get stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin layer of it and allow it to soak into the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you are not ready to replace the hinges on your door, you are able to make a few minor repairs. Make sure the screws that secure the hinge plate to the door frame as well as the frame are tight. If they're loose, tighten them using an electric drill or screwdriver. Be careful not to over tighten the screws as this can cause gaps to form at the trim joints, or worse, strip the threads.

If the problem is that the hinge plates are separated from the door and jamb, you can reattach them by gluing wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will serve as a solid base for the screws and help prevent the plates from shifting when you drive them into place. Allow the glue to dry before reattaching your hinge.

The screws could also be stripped or missing. This can be corrected by replacing the screws. Use a drill that is similar to the size of the screw hole to prevent drilling into the jamb or hinge.

Close the door after you have reattached your hinge and check the gap between the frame and the door. The gap should be about the thickness of a penny or less if an older door was not properly hung. If the hinges were installed correctly, this should not be an issue.

If the hinges are still loose, you can add an extra thick hinge between the surface of the hinge plate and the mounting surface. This will give the hinges a little more room. You could also try removing the hinge pin from the problem hinge and pounding it down using a hammer to make it tighter or use a new hinge pin altogether. It is also possible to lubricate the hinges using mineral or jojoba oil to decrease friction and aid in holding their place. Lubricating your hinges regularly will help prevent them from becoming stiff and squeaky and also prolong their lifespan.

Cleaning the Hinges

The friction created by a hinge's constant movement attracts dust particles. If there is no regular cleaning or lubrication, the particles become stuck in the moving parts of a hinge for doors and then build up over time. The hinge will become stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection can help preserve the quality of a door's hinges and ensure their proper operation.

Examine the hinges for signs of corrosion. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you're able to save the hinges, remove any loose rust using wire brush and steel wool. Then, apply an industrial rust remover or a homemade solution, such as lemon juice to the hinge. Allow the rust-removing solution to sit on the hinges for several minutes in order to penetrate and dissolve the remaining rust.

Retightening screws can restore hinge functionality in the event that you don't want to spend time or money on repairing hinges. If you've sanded the screw holes, however, it may be necessary to attach an wooden dowel or shim to the hinge. Dowels made of wood come in round rods of varying lengths and sizes. They are available at home improvement centers or woodworking supply shops, or online.

You can also create an shim out of made of plastic or metal depending on the kind of hinge you own. To make a dowel cut a dowel from wood to the desired length. You can then dip the dowel in a glue for carpenters and then insert it into the stripped hole, allowing the glue to hold the dowel in the desired position.

Before you begin cleaning the hinges, lay down a paper or cloth towel to protect flooring and other surfaces from spills and drips that may happen. After securing the area clean the hinges with a soft sponge or cloth coated with mild cleaner to eliminate dirt, grime, and tarnish. A small brush or toothbrush can be used to reach difficult-to-reach spots in crevices or narrow spots.